Zubehör-Artikel von Hailege(37 Treffer)
3D-Technik
Produktart
3D Drucker & Scanner
Variante
Zubehör-Artikel
Kategorie
Farbe
0-25 €
Preis
Increase 5V power output, the output I / O port protection are not afraid of operational errors caused...
Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step....
GP2Y0E03 Infrared Distance Measurement Sensor Module Infrared LED and CMOS image sensor, built-in signal...
RF input: + 10dBm (1dB compression point) RF input: 0.1-500MHz Local oscillator input: 0.1-500MHz IF...
Finger Heartbeat Measure Sensor 5V Heartbeat Detect Sensor Heart Rate Detect Sensor INT led Pin=13, INT...
Object is sensed output 0, output 1 is not sensitive to the time, directly with 3V and 5V microcontroller...
SPI interface, the control signal line leads VS1053 can play a variety of music formats, also supports...
Power Supply: 3V-5V; Measuring range: ±1.3-8 gauss GY-271 QMC5883L 3-5V IIC Triple Axis Compass Magnetic...
The step down regulator adopts synchronous rectification scheme to provide wide voltage range, large...
I2C interface up to 400 kbit/s, Pull-up voltage from 1.8V to 3.3V Nine gesture recognition (Up / Down...
Operating Voltage: 2.7V - 8.5V; Operating Current: 1A LTC4150 Coulomb Counter Current Detection Sensor;...
On-board High precision TI ADS1256IDB ADC chips Data output rates up to 30ksps, nonlinearity is low to...
Dual H-Bridge PWM Stepper Speed Controller Board L298N L298 DC Motor Driver Drive Board Dual H-bridge...
This is the "momentary" variety of the touch sensor - touch and it turns on, release and it turns off....
Support Most Cortex-M Chips with SWD Virtual Serial Port DAPLINK Simulation Download Burner The CDC serial...
Working voltage: DC 10-35V; Rated maximum output: ± 3A, peak 3.5A. TB6560 3A CNC Router Single 1 Axis...
Resistance value: R (25 ° C) = 100K ± 1% 100K ohm NTC 3950 Thermistors B value: B = 3950 ± 1%
Heater/MOSFET outputs and three fan thermistor circuit. RAMPS 1.4 Control Panel 3D Printer Control Board...
A single module can drive a 8x 8 dot matrix common cathode 8x8 Dot Matrix LED Module Four in One Dot...
ESP8285 ESP-01M IR Infrared Transmitter Receiver Module Work Voltage:DC 5V; Size:23.4*23.4*18mm Support...
9V-42V DC power supply, H bridge bipolar constant phase flow drive. TB6600 Stepper Motor Driver 32 Segments...
Includes 10 Sizes: 0.15/ 0.2/ 0.25/ 0.3/ 0.35/ 0.4/ 0.5/ 0.6/ 0.8/ 1.0mm 3D Printer Nozles Cleaning Needles...
The L298P shield DC motor driver has PWM speed control mode; dual high-power H-bridgedriver. Driven part...
3D Printer Motor Drive Converter Expansion Adapter 3D Printer Motor Drive Converter Adapter Suitable...
With Voltmeter Ammeter Display 5A Constant Current/Voltage LED Driver Battery Charging Module Input voltage:...
3D Printer Stepper Motor Driver CNC Shield V4 Engraving Machine Expansion Board Compatible with micro-drive...
Flyback Heater Driver Board ZVS 20A 1000W Low Voltage Induction Heating Module 24V input with no load...
The I2S is a small, low cost MEMS mic with a range of about 50Hz - 15KHz, good for just about all general...
Intelligent Car Infrared Tracking Probe Tracing Sensor TCRT5000 5V 1 Way Tracing Module Tracing Sensor...
Built-in regulator (no external logic voltage supply needed) RV8825 Stepper Motor Drive Module for 3D...
MAX4466, an op-amp specifically designed for amplifier, comes with a 20-20KHz electret microphone soldered...
VEML7700 Ambient Light Sensor Module I2C IIC 16 Bits 0~120k Lux Light Measuring This module requires...
PCA9306 I2C Level Translator Breakout Board Module 2-bit bidirectional translator for SDA and SCL lines...
Communication Interface: IIC; 16-way steering gear control PCA9685 16 Channel IIC I2C 12-Bit PWM Servo...
STM32F030F4P6 Minimum System Board(Cortex-M0) Frequency up to 48 MHz, high-speed embedded memories Main...
Temperature sensor 100KΩ accuracy of ± 1% 3D Printer 100K ohm NTC 3950 Thermistors Sensor Wiring length:...
Work for 3D Printer RAMPS 1.4 Reprap Mendel Prusa 3D Printer Reprap Smart Controller 12864 LCD Display...